+27 21 852 4719 [email protected] Mon-Fri 8:00-17:30 (SAST)
Liquid Level Control Floats

Liquid Level Control Floats

Browse technical resources about OM5/OS2 fiber, FC/ST connectors, distribution boxes, circulators, QSFP28, PDU, FTTR, rail transit and communication cabling.

  • Domestic Fiber Optic Liquid Level Sensor

    Domestic Fiber Optic Liquid Level Sensor

    Mountable on transparent piping with an outer diameter of 6 to 26 mm and a wall thickness of 1 to 3 mm for detecting the upper level of the internal water surface. Offers heat resistance up to 100°C. Equipped with a mounting position adjusting lever for easy installation. In this paper, a novel liquid level sensing system is proposed to enhance the capacity of the sensing system, as well as reduce the cost and increase the sensing accuracy. The “Plug & Forget”. FU-95Z, Liquid-level-detection Fiber Unit in FS-N40 series by KEYENCE America. A liquid accumulation prevention structure is used for all liquid level contact type models.


  • Are light control modules reliable

    Are light control modules reliable

    Wired modules use physical cables to connect to switches, dimmers, or control panels. A lighting control module is the “control center” for your lighting system. It acts as a bridge between your physical lighting fixtures and the smart systems that manage them. Think of it as the “brain” that receives commands—either from a manual switch, a sensor, or a building automation system—and translates them into. Each approach has distinct advantages, disadvantages, installation requirements, and ideal use cases. These innovative devices simplify your daily routine by managing brightness levels and reducing unnecessary energy consumption. We believe that managing your home. Through advanced technologies like LED dimmer modules, and Bluetooth-enabled devices, lighting control systems are creating adaptable, energy-efficient environments that respond to the needs of their occupants.

    [PDF Version]
  • Does the elevator machine room necessarily need a separate electrical control box

    Does the elevator machine room necessarily need a separate electrical control box

    All major elevator manufacturers are offering machine room-less (MRL) systems. These systems eliminate the need for a separate room to house hydraulic pumps, control panels, etc. The controller must still be located so. Each car, machine room and hoistway pit must have separate dedicated branch circuits for lighting, receptacles and HVAC, with car and machine-room lighting exempt from GFCI while required for receptacles. Overcurrent devices and disconnects must be located in machine or control spaces, be lockable. A look at Article 620. Is there not? Has this changed OR should I be looking in the, in this case MA, elevator code for. A machine room is an area where the elevator drive unit, controller, and main disconnect switches are located. However, they do present some challenges.


  • Function of Huawei Core Switch Main Control Board

    Function of Huawei Core Switch Main Control Board

    The Huawei H901MPLB is the main control card (MPLB) for the SmartAX MA5800 Next-Generation OLT. CloudEngine S8700 series smart routing switches (S8700 for short) are high-end switches designed by Huawei for next-generation enterprise networks. The S8700 series uses Huawei's intelligent multi-layer switching technology to provide intelligent service optimization methods, such as VPN, service. Device management and monitoring module: provides the controller area network bus (CAN Bus) module to monitor the SRU and LPU CAN Bus modules. It is designed for high reliability, featuring active/standby switchover and load sharing to. It adopts a fully programmable architecture to meet the flexible and fast customization needs of users, and help users to smoothly evolve the network to SDN (Software-Defined Networking). You are advised to perform this step when Wi-Fi needs to be used immediately.

    [PDF Version]
  • Relay Protection Safety Control Method List

    Relay Protection Safety Control Method List

    The objective of relay protection is to quickly isolate a faulty section from both ends so that the rest of the system can function satisfactorily. The functional requirements of the relay:.


Need Product Pricing?

Contact us for competitive quotes on any of our fiber optic and telecom products

Get a Quote