+27 21 852 4719 [email protected] Mon-Fri 8:00-17:30 (SAST)
Kitchen And Home – Design

Kitchen And Home – Design

Browse technical resources about OM5/OS2 fiber, FC/ST connectors, distribution boxes, circulators, QSFP28, PDU, FTTR, rail transit and communication cabling.

  • What size wireless router should I use if I have a 100Mbps fiber optic connection at home

    What size wireless router should I use if I have a 100Mbps fiber optic connection at home

    For fiber optic internet speeds of 100 Mbps or higher, a router supporting at least 1 Gbps is required. Look for routers with AX or AC designations (Wi-Fi 5 or 6) that support faster speeds than older N standards (Wi-Fi 4). Let's delve into the best WiFi routers suited for unleashing the full potential of your 100 Mbps connection. Source: Amazon Best Security: NETGEAR Nighthawk Modem Router Combo C7000 Pros: Cons: The NETGEAR C7000-100NAS stands out by combining a cable modem and WiFi router into one device, offering. Popular internet service providers (ISPs) such as Cox, Spectrum, Xfinity, and fiber-optic providers like AT&T offer faster Internet speeds for expansive home WiFi networks. Range. The two main ways to set up such a network are by connecting these additional access points to your main router with a cable or wirelessly, also known as wired or wireless backhaul. It has plenty of power and shares some of the networking features typically available in high-end.

    [PDF Version]
  • System Relay Protection Design

    System Relay Protection Design

    Relay protection is the discipline of designing schemes that detect faults, coordinate relays, and isolate equipment without outages. Power System Protective Relays: Principles & Practices Protective Relays - Technical Seminar Nov 2016 - Copyright: IEEE 1 Power System Protective Relays: Principles & Practices Presenter: Rasheek Rifaat, P. Eng, IEEE Life Fellow IEEE/IAS/I&CPSD Protection & Coordination WG Chair Jacobs Canada. presentation of protection and control relaying. The report will identify methodology behind these practices, present issues raised by the integration of microprocessor relays and the internal logic and external communication configurations, ying. Abstract: To protect personnel, equipment, and maintain continuity of service for an electrical system, protection or fault interrupting devices are required. System. This handbook covers the code of practice in protection circuitry including standard lead and device numbers, mode of connections at terminal strips, colour codes in multicore cables, dos and donts in execution.

    [PDF Version]
  • Tubular Aluminum Busbar Design

    Tubular Aluminum Busbar Design

    Aluminum Tubular Busbar is a hollow cylindrical conductor used in power distribution systems for efficient high-current transmission. Compared to traditional solid busbars, its tubular design offers several advantages, including lightweight, high mechanical strength, and excellent. Aluminium tubular busbar is a conductor used in power systems for transmitting large currents, made of high-purity aluminium or aluminium alloys, typically in a round hollow tube structure. It is typically made from 6101 aluminum alloy, which offers an excellent balance of conductivity and mechanical strength. Our extensive industry. Commonly used insulation materials are: Nomex®, Tedlar®, Mylar®, Kapton®, Ultem®, Mylar/Tedlar, Tedlar/Mylar/Tedlar, Valox®, epoxy-glass, heat shrink tubing, and epoxy powder coating. There are many different thicknesses of these insulation materials available. Contact a Mersen engineer for more.

    [PDF Version]
  • Why do relay protection systems use a three-stage design

    Why do relay protection systems use a three-stage design

    Modern practice is to adopt definite distance method of protection applied in 3 zones (steps). A number of distance relays are used in association with timing relays so that the power system is divided into a number of zones with varying tripping times associated with each. This protection relay configuration consists of three distinct stages: Instantaneous Overcurrent Protection (Stage I), Time-Limited Overcurrent Protection (Stage II), and Definite-Time Overcurrent Protection (Stage III). The protection relay's core functionality lies in its graded coordination. Protective relays and devices have been developed over 100 years ago to provide “lastline”of defense for the electrical systems. Instantaneous Overcurrent Protection (Stage 1): No intentional time delay. This document provides recommendations, background and philosophy on relay protection that is not available in M07. In this paper, on the basis of the features of the relay protection in the power line, thorough research and the analysis of relay protection both at home and abroad, with the aid of MATLAB/Simulink to build simulation model, Using PSB module to construct a three-stage over-current protection's.

    [PDF Version]
  • Key Design Considerations for Small Busbars

    Key Design Considerations for Small Busbars

    Learn how to design custom power busbars, including current rating, material selection, thickness, width, and hole pattern considerations. The busbar electrical system performs several essential functions that support efficient power management: Power Distribution: It is a central station to which the electrical power is brought out of one source and to more than one circuit. A busbar is a metal bar, usually made of copper or aluminum, that carries electricity inside switchgear. Power Busbar Current Rating The current rating determines: High-current applications often use multiple parallel busbars instead of a single thick bar. An electrical busbar is a solid.


  • The IDC server rack adopts a closed cold aisle design

    The IDC server rack adopts a closed cold aisle design

    The system simply aligns server fronts (air intakes) toward a shared cold aisle, and backs (exhausts) toward a shared hot aisle. Hot aisle and cold aisle containment are foundational concepts in data center design. In this guide, we'll break down how hot aisle and cold aisle configurations. Cold aisle containment (CAC) is a proven data center cooling strategy that creates physical barriers around cold air supply zones, preventing contamination from hot exhaust air and eliminating the energy-wasting effects of air mixing.


  • Engineering Design in the Telecommunication Tower Industry

    Engineering Design in the Telecommunication Tower Industry

    This comprehensive article examines the critical aspects of structural evaluation in telecommunications towers, addressing key considerations in design, load analysis, and safety protocols. The article encompasses various tower configurations, including lattice, monopole, and guyed structures. industry is undergoing a significant transformation. New tower designs are being developed and existing towers are being reinforced based on emerging technologies, sustainability concerns, and the demand for safer, more vers with the ability to handle higher volumes of trafic.


Need Product Pricing?

Contact us for competitive quotes on any of our fiber optic and telecom products

Get a Quote